| 232.20.1000.013 Type 21/1200.2 Standard 5 Slewing Ring Bearings | J min.:234.95 mm; da:74.612 mm; H2:47.625 mm; d2:111.125 mm; A:76.2 mm; J max.:247.65 mm; Basic dynamic load rating C:158 kN; B:92.075 mm; A1:99.219 mm; Limiting speed:2800 r/min; S:0.794 mm; Attachment bolt diameter G:19.05 mm; L:304.8 mm; H:160.338 mm; Mass bearing unit:10.9 kg; s:31.75 mm; H1:79.375 mm; |
| 92.25.1310.991.21.1503 Standard 5 Slewing Ring Bearings | Da:180 mm; P150°:58.7 kN; H1:114.3 mm; S:4.763 mm; RG:3/8 NPT; P60°:175 kN; H2:44.45 mm; R1:58.737 mm; da:84.138 mm; PosiTrac Plus contact element:2 x B10724-102; P120°:64.9 kN; Stabilizing ring:SR-20-17; A2:155.575 mm; P180°:71.2 kN; J max.:333.375 mm; Cap bolt:5/8-11 UNC; Pa:13.8 kN; Appropriate attachment bolt size G:0.75 in; Initial grease fill:181.44 g; Labyrinth ring:2 x LOR 100; |
| 12.35.1960.400.11.1503 Standard 5 Slewing Ring Bearings | Sealed Speed Rating n3:4300 rpm; Accessories:Two Seals & Snap-Rin; d:60.000 mm; Basic Static Radial Load Rating Co:25000 N; B:18.00 mm; Basic Dynamic Radial Load Rating C:32500 N; D:95.0000 mm; Grease Speed Rating Open/Shielded n1:6700 rpm; Oil Speed Rating Open/Shielded n2:8000 rpm; Fillet Radius ra:1.00 mm; |
| 161.25.1180.890.11.1503 Standard 5 Slewing Ring Bearings | Preload class A GA:92 N; Mass bearing:0.43 kg; D2:85.4 mm; r3,4 min.:0.6 mm; Basic static load rating C0:12.9 kN; d2:70.6 mm; db max.:70 mm; d1:72.74 mm; db min.:66 mm; B:18 mm; Basic dynamic load rating C:17.2 kN; Calculation factor f0:8.5; Preload class B GB:275 N; da min.:66 mm; ra max.:1 mm; Calculation factor f2B:1.03; Db max.:90.8 mm; Preload class C GC:550 N; Calculation factor fHC:1; Fatigue load limit Pu:0.54 kN; |
| 91.25.1154.990.11.1503 Standard 5 Slewing Ring Bearings | N1:19.05 mm; L:279.4 mm; Pa:6.09 kN; A2:184.15 mm; RG:1/8 NPT; S:3.969 mm; Max. speed for Taconite seal:1400 r/min; Mass pillow block:10.8 kg; P60°:50.3 kN; Cap bolt, SAE grade:5; Cap bolt recommended tightening torque:81.3 N·m; P150°:16 kN; R2:15.875 mm; End plug (suffix Y):EPR 6; Cap bolt:2 x 1/2-13 UNC; Ca:39.014 mm; h:27.781 mm; Da:120 mm; P180°:19.1 kN; P90°:30.2 kN; |
| 92.20.1006.991.21.1503 Standard 5 Slewing Ring Bearings | K:4 mm; D:240 mm; Fatigue load limit Pu:76.5 kN; ra max.:1.5 mm; das:203 mm; B:50 mm; Mass bearing:5.65 kg; Reference speed:1100 r/min; Basic static load rating C0:750 kN; d1 ≈:209 mm; Calculation factor kr:0.2; Limiting speed:1400 r/min; da min.:197 mm; Basic dynamic load rating C:358 kN; D1 ≈:219 mm; b1:7 mm; d:190 mm; r1,2 min.:1.5 mm; Da max.:233 mm; |
| 92.30.1415.991.21.1502 Standard 5 Slewing Ring Bearings | J6:83 mm; Housing material:Cast iron; A3:3.2 mm; J:70 mm; B:34.1 mm; Recommended tightening torque for grub screw:4 N·m; Basic static load rating C0:7.8 kN; Da:74.6 mm; A1:12 mm; Thread grub screw G2:1/4-28 UNF; Hexagonal key size for grub screw N:3.175 mm; N:11.5 mm; Mass bearing unit:0.73 kg; RG:1/4-28 UNF; Limiting speed:7000 r/min; J7:19 mm; Basic dynamic load rating C:14 kN; Recommended diameter for attachment bolts, mm G:10 mm; |
| 282.30.1475.013 Type 110/1600.2 Standard 5 Slewing Ring Bearings | Permissible sliding velocity v max.:5 m/s; Mass bushing:0.086 kg; Tolerance housing:H7; d:14 mm; Tolerance shaft:h8; D:28 mm; Specific dynamic load factor K:10 N/mm²; Specific static load factor K0:20 N/mm²; Permissible sliding velocity v min.:0.25 m/s; Coefficient of friction µ max.:0.1; B:30 mm; Coefficient of friction µ min.:0.05; |
| 161.28.1700.890.11.1503 Standard 5 Slewing Ring Bearings | Db min.:174 mm; ra max.:3.5 mm; Calculation factor Y0:1.1; Dimension series:48200; Cb min.:6 mm; a:34.02 mm; r1,2 min.:3.5 mm; Mass bearing:3.3 kg; Ca min.:6 mm; Basic dynamic load rating C:281 kN; Fatigue load limit Pu:44 kN; d1 ≈:154.5 mm; Reference speed:2600 r/min; T:39.688 mm; Da min.:165 mm; da max.:140 mm; d:127 mm; r3,4 min.:3.3 mm; Da max.:169 mm; Calculation factor Y:2; |
| 61.20.0944.500.01.1503 Standard 5 Slewing Ring Bearings | S:4.763 mm; L:349.25 mm; H:192.088 mm; PG:1/8 NPT; R1:60.325 mm; Cap bolt recommended tightening torque:298.3 N·m; ba:44.45 mm; Stabilizing ring:SR-18-15; da:60.325 mm; A2:149.225 mm; P150°:34.7 kN; P180°:42.3 kN; RG:3/8 NPT; A1:98.425 mm; Cap bolt:2 x 5/8-11 UNC; J1:53.975 mm; H1:101.6 mm; Initial grease fill:141.75 g; P90°:60.9 kN; P120°:38.3 kN; |
| 161.25.1320.891.21.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:78100 N; Grease Speed Rating n1:3800 rpm; B:36.50 mm; Fillet Radius ra:1.50 mm; Sealed Speed Rating n3:3800 rpm; Basic Static Radial Load Rating Co:88000 N; D:110.0000 mm; Accessories:Two Shields & Snap-R; Oil Speed Rating n2:5000 rpm; d:60.000 mm; |
| 62.40.1500.000.19.1504 Standard 5 Slewing Ring Bearings | r1,2 min.:1.5 mm; d:160 mm; B:15 mm; Mass shaft washer:2.3 kg; d1:222 mm; |
| 282.30.0900.013 Type 110/1100.2 Standard 5 Slewing Ring Bearings | Cap bolt, SAE grade:8; Ca:37.008 mm; R1:46.038 mm; S:3.175 mm; H1:82.55 mm; P180°:30.7 kN; RG:1/4 NPT; Housing:FSAFS 515; J min.:219.075 mm; Cap bolt recommended tightening torque:149.1 N·m; P90°:45.4 kN; L:285.75 mm; Appropriate attachment bolt size G:0.5 in; H2:30.163 mm; Stabilizing ring:SR-15-0; Max. speed for Taconite seal:1250 r/min; Taconite seal:TER 36; End plug (suffix Y):EPR 7; |
| 11.20.0971.001.21.1504 Standard 5 Slewing Ring Bearings | Accessories:One Shield & Snap-Ri; D:150.0000 mm; Oil Speed Rating n2:5300 rpm; Fillet Radius ra:2.00 mm; Sealed Speed Rating n3:3000 rpm; Grease Speed Rating n1:4500 rpm; Basic Static Radial Load Rating Co:68000 N; d:70.000 mm; Grease Speed Rating Open/Shielded n1:4500 rpm; Basic Dynamic Radial Load Rating C:104000 N; B:35.00 mm; Oil Speed Rating Open/Shielded n2:5300 rpm; |