| 62.25.1455.500.11.1503 Standard 5 Slewing Ring Bearings | GN:1/4-28 SAE-LT; J max.:181 mm; Housing material:Cast iron; J min.:162 mm; H1:63.5 mm; Recommended tightening torque for grub screw:16.5 N·m; A:60 mm; DN:6.5 mm; Thread grub screw G2:3/8-24 UNF; H:126 mm; Basic static load rating C0:29 kN; A5:37.5 mm; Limiting speed:3600 r/min; H2:24 mm; B:55.6 mm; Hexagonal key size for grub screw N:4.763 mm; N:27.5 mm; SWN:7 mm; Recommended diameter for attachment bolts, inch G:0.625 in; |
| 232.20.1000.503 Type 21/1200.2 Standard 5 Slewing Ring Bearings | s1:25.8 mm; Recommended diameter for attachment bolts, inch G:0.5625 in; A3:3.2 mm; H:178.5 mm; Recommended diameter for attachment bolts, mm G:14 mm; L:111 mm; B4:7 mm; Rα:45 °; GN:1/4-28 SAE-LT; Basic dynamic load rating C:33.2 kN; SWN:7 mm; J6:120.5 mm; Da:98.4 mm; Limiting speed:4300 r/min; Thread grub screw G2:5/16-24 UNF; J7:18 mm; A1:14 mm; N:16 mm; R1:24.5 mm; Db1:102 mm; |
| 92.30.1607.991.21.1502 Standard 5 Slewing Ring Bearings | A2:119.063 mm; Cap bolt recommended tightening torque:81.3 N·m; PG:1/8 NPT; L:285.75 mm; Cap bolt:2 x 1/2-13 UNC; Appropriate attachment bolt size G:0.625 in; Ca:37.008 mm; Housing:SAF 515; Labyrinth ring:2 x LOR 37; End plug (suffix Y):EPR 7; R1:46.038 mm; H2:28.575 mm; Stabilizing ring:SR-15-0; P120°:28 kN; Max. speed for PosiTrac Plus seal:2350 r/min; PosiTrac Plus contact element:2 x B10724-37; |
| 161.36.1800.890.11.1503 Standard 5 Slewing Ring Bearings | Basic Dynamic Radial Load Rating C:572000 N; Grease Speed Rating n1:1700 rpm; Oil Speed Rating n2:2100 rpm; Fillet Radius rb:1.00 mm; Fillet Radius ra:3.00 mm; D:300.0000 mm; d:140.000 mm; Basic Static Radial Load Rating Co:800000 N; B:124.00 mm; |
| 62.30.1120.001.21.1504 Standard 5 Slewing Ring Bearings | J1:114.3 mm; Da:339.999 mm; Initial grease fill:1672.65 g; PosiTrac Plus contact element:2 x B10724-167; R2:42.069 mm; Mass pillow block:208 kg; H:400.05 mm; J min.:549.275 mm; Ca:101.803 mm; Eye bolt:2 x 1/2-13 UNC; P180°:160 kN; Labyrinth ring:2 x LOR 166; P120°:151 kN; P150°:136 kN; R1:120.65 mm; End plug (suffix Y):EPR 23; H1:200.025 mm; P60°:416 kN; Stabilizing ring:2 x 36053-140; |
| 162.25.1077.891.21.1503 Standard 5 Slewing Ring Bearings | Bearing limiting speed:2600 r/min; Ca:95.809 mm; L:628.65 mm; A1:171.45 mm; P150°:113 kN; N1:28.575 mm; Stabilizing ring:SR-34-0; Pa:43.6 kN; Cap bolt, SAE grade:8; H2:69.85 mm; H1:179.4 mm; J1:107.95 mm; J max.:549.275 mm; J min.:492.125 mm; Da:309.999 mm; Appropriate attachment bolt size G:1 in; RG:3/4 NPT; H:360.363 mm; Cap bolt:1-8 UNC; Eye bolt:2 x 3/8-16 UNC; |
| 12.25.1600.000.11.1503 Standard 5 Slewing Ring Bearings | Grease Speed Rating n1:6300 rpm; Basic Static Radial Load Rating Co:29000 N; Oil Speed Rating n2:8500 rpm; d:30.000 mm; Basic Dynamic Radial Load Rating C:41600 N; B:30.20 mm; Sealed Speed Rating n3:6300 rpm; D:72.0000 mm; Accessories:One Shield & Snap-Ri; Fillet Radius ra:1.00 mm; |
| 61.40.1600.008.19.1503 Standard 5 Slewing Ring Bearings | Basic Static Radial Load Rating Co:390000 N; d:420.000 mm; Accessories:Two Seals; D:520.0000 mm; B:46.00 mm; Basic Dynamic Radial Load Rating C:251000 N; Grease Speed Rating Open/Shielded n1:950 rpm; Oil Speed Rating Open/Shielded n2:1200 rpm; Sealed Speed Rating n3:0 rpm; Fillet Radius ra:2.00 mm; |
| 91.20.1146.991.21.1503 Standard 5 Slewing Ring Bearings | Mass bushing:0.023 kg; B:30 mm; Tolerance housing:H7; Tolerance shaft:h8; Coefficient of friction µ min.:0.05; Permissible sliding velocity v min.:0.25 m/s; Permissible sliding velocity v max.:5 m/s; D:22 mm; Specific dynamic load factor K:10 N/mm²; Coefficient of friction µ max.:0.1; Specific static load factor K0:20 N/mm²; d:18 mm; |
| 162.36.1700.891.41.1503 Standard 5 Slewing Ring Bearings | B:16 mm; da max.:37.3 mm; Mass bearing:0.21 kg; Basic static load rating C0:11.2 kN; Calculation factor kr:0.025; Da max.:56.4 mm; Limiting speed:7500 r/min; da min.:35.6 mm; Basic dynamic load rating C:20.3 kN; d2 ≈:37.3 mm; ra max.:1 mm; Fatigue load limit Pu:0.475 kN; d:30 mm; Calculation factor f0:13.8; r1,2 min.:1 mm; D:62 mm; D2 ≈:54.06 mm; |
| 281.30.1475.013 Type 110/1600.1 Standard 5 Slewing Ring Bearings | Max. speed for Taconite seal:560 r/min; Pa:49.8 kN; Mass pillow block:109 kg; Da:289.999 mm; PG:1/4 NPT; Cap bolt:4 x 3/4-10 UNC; ba:82.55 mm; A1:158.75 mm; P60°:226 kN; Housing:SAW 532; Ca:113.817 mm; P150°:78.3 kN; N1:28.575 mm; S:4.763 mm; J min.:441.325 mm; da:136.525 mm; P180°:94.3 kN; RG:3/4 NPT; P90°:136 kN; R1:104.775 mm; |
| 60.25.1355.500.11.1503 Standard 5 Slewing Ring Bearings | Sleeve:S 118x3.1/4; B4:19.863 mm; d3 max.:118.389 mm; G:89.586 mm; Hydraulic nut:HMVC 18E; B1:89.992 mm; d:90 mm; Threads per inch:12; Mass adapter sleeve assembly:1.8 kg; B:17.729 mm; d1:82.55 mm; |
| 62.25.1180.001.21.1504 Standard 5 Slewing Ring Bearings | Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:8500 rpm; Accessories:Two Seals; D:62.0000 mm; B:17.00 mm; Basic Static Radial Load Rating Co:10800 N; Basic Dynamic Radial Load Rating C:22900 N; Oil Speed Rating Open/Shielded n2:15000 rpm; Grease Speed Rating Open/Shielded n1:12000 rpm; d:17.000 mm; |
| 192.25.1800.990.41.1502 Standard 5 Slewing Ring Bearings | Bearing designation:619 / 5 ; Static (Cor):0.432 kN; da:6.6 min; Weight:0.0025 kg; d:5 mm; D:13 mm; Pu:0.020 kN; Da:11.5 max; Grease:47 000 min-1; rs:0.2 mm; Dynamic (Cr):1.079 kN; ra:0.2 max; Oil:56 000 min-1; B:4 mm; |